lnu.sePublications
Planned maintenance
A system upgrade is planned for 17/11-2026, at 12:00-13:00. During this time DiVA will be unavailable.
Change search
Link to record
Permanent link

Direct link
Publications (10 of 18) Show all publications
Binder, E., Kuck, E., Bertram, C., Shehadeh, Z., Schweigler, M., Sandhaas, C. & Bader, T. K. (2026). Stiffness and strength of beech, birch and spruce in compression perpendicular to the grain and rolling shear: Influence of moisture content, annual ring structure, and test method. Construction and Building Materials, 538, Article ID 147142.
Open this publication in new window or tab >>Stiffness and strength of beech, birch and spruce in compression perpendicular to the grain and rolling shear: Influence of moisture content, annual ring structure, and test method
Show others...
2026 (English)In: Construction and Building Materials, ISSN 0950-0618, E-ISSN 1879-0526, Vol. 538, article id 147142Article in journal (Refereed) Published
Abstract [en]

For an efficient material utilization of hardwood in engineering applications, mechanical properties and their relationships to the structure of the material are required. Herein, rolling shear (RS) and compression perpendicular to grain (CPG) stiffness and strength of southern Swedish beech, birch, and spruce were experimentally investigated. The experimental testing champaign consisted of (i) tests in three different ambient climates to quantify the moisture content (MC) influence and (ii) tests on two different characteristic scales to quantify the difference between the testing methods, and thus the influence of the annual ring structure. Since the analysis of variance for the investigated groups of different ambient climates yielded low statistical significance, a board-wise quantification method was applied. The effects of variations in density and annual ring structure were minimized by comparing samples from the same board. RS properties were equally influenced by moisture content in hardwood and spruce, while CPG properties of hardwood were stronger influenced by moisture content than spruce properties. Comparing results from the two different specimen sizes showed that the cylindrical orthotropic structure in the cross-section of boards substantially increased the effective RS strength as compared to smaller scale tests, whereas a weaker opposite trend was observed for CPG strength. RS and CPG stiffness were quite similar on both scales. The influence of the annual ring inclination on the material scale was further compared to multiscale material models for hardwood and softwood. The models showed that hardwood properties are stronger influenced by the density and much less by the annual ring inclination than properties of spruce, in agreement with the experimental analysis.

Place, publisher, year, edition, pages
Elsevier, 2026
Keywords
hardwood, softwood, experimental investigation, rolling shear rs, compression perpendicular to the grain cpg, timber properties, en 408 standard tests, shear modulus, elastic modulus
National Category
Composite Science and Engineering
Research subject
Technology (byts ev till Engineering), Forestry and Wood Technology
Identifiers
urn:nbn:se:lnu:diva-148864 (URN)10.1016/j.conbuildmat.2026.147142 (DOI)001818458300001 ()2-s2.0-105043506445 (Scopus ID)
Available from: 2026-07-27 Created: 2026-07-27 Last updated: 2026-08-17Bibliographically approved
Schweigler, M., Binder, E., Lemaitre, R. & Bader, T. K. (2026). Tension test setups for embedment testing of doweled timber connections loaded parallel and perpendicular to the grain. Construction and Building Materials, 521, Article ID 146063.
Open this publication in new window or tab >>Tension test setups for embedment testing of doweled timber connections loaded parallel and perpendicular to the grain
2026 (English)In: Construction and Building Materials, ISSN 0950-0618, E-ISSN 1879-0526, Vol. 521, article id 146063Article in journal (Refereed) Published
Abstract [en]

Embedment strength and foundation moduli are key parameters for predicting the load-carrying and displacement capacity of laterally loaded doweled connections in timber structures. Despite their importance, knowledge of the long-term mechanical behavior of such connections remains limited, partly due to challenges in experimentally determining these parameters. This study aims to develop and evaluate a tensile test setup for investigating the embedment behavior of timber, suitable for both short-term and long-term measurements. A full-hole embedment test setup for loading specimens in tension parallel and perpendicular to the grain was designed through a combined numerical–experimental approach. The suitability of the setup was examined by conducting comparative experiments using this newly developed tension method and a conventional compression setup. Specimens for both setups were sourced from the same material and prepared under consistent procedures, allowing an isolated systematic assessment of potential differences in embedment strength and foundation moduli. The results demonstrate that the tension embedment test setup provides valid and reliable measurements, with only minor and not statistically significant deviations from the compression test setup. The proposed tension test setup offers a practical alternative to the established compression approach and is particularly advantageous for long-term testing, as it enables efficient and stable loading by stacking multiple specimens in a tensile chain configuration.

Place, publisher, year, edition, pages
Elsevier, 2026
Keywords
Embedment strength, Foundation modulus, Doweled timber connections, Tension test setup, Parallel and perpendicular to the grain loading, Full-hole embedment test
National Category
Building Technologies Wood Science
Identifiers
urn:nbn:se:lnu:diva-145735 (URN)10.1016/j.conbuildmat.2026.146063 (DOI)001734813200001 ()2-s2.0-105034387187 (Scopus ID)
Funder
Swedish Research Council Formas, 2022-01367
Available from: 2026-03-31 Created: 2026-03-31 Last updated: 2026-04-13Bibliographically approved
Quarcoo, F., Myhren, J. A., Binder, E. & Dodoo, A. (2026). Towards Circularity in Multi-Storey Wood Buildings: a Systematic Literature Review. Circular Economy and Sustainability, 6, Article ID 373.
Open this publication in new window or tab >>Towards Circularity in Multi-Storey Wood Buildings: a Systematic Literature Review
2026 (English)In: Circular Economy and Sustainability, ISSN 2730-597X, E-ISSN 2730-5988, Vol. 6, article id 373Article in journal (Refereed) Published
Abstract [en]

In an era of environmental awareness, the construction industry faces pressure to adopt resouurce-efficient practices that reduce waste, extend material lifespans, and support climate change mitigation. While the environmental benefits of multi-storey wood buildings (MWBs) are well recognized, understanding and evaluating circular economy (CE) applications in this context remains limited. This study explores CE strategies for MWBs, examines circularity indicators, tools and methods for evaluating CE, and identifies challenges hindering the application of CE in MWB construction through a systematic literature review. Following the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) protocols, a structured search was conducted in the Web of Science and Scopus databases using relevant keywords. A total of 34 relevant studies were selected from an initial list of 347 studies. The results indicate that key CE strategies were increasingly implemented at the early-stage of MWBs. However, limited CE implementation exist at the end-of-life stage of MWBs. Key challenges to CE MWB construction include risk-averse approach of designers and engineers, the lack of standardized data and methodologies for end-of-life assessment, insufficient conceptualization and categorization of CE principles due to limited knowledge and education, and limitations in current life cycle assessment methods. The study highlights significant limitations in circularity indicators and evaluation methods, emphasizing the need for further research to advance CE integration in MWBs. By systematically synthesizing the state-of-the art research on CE practices in MWBs, this study presents a framework that highlights key challenges, knowledge gaps, and research priority areas for advancing circularity in MWBs.  

Place, publisher, year, edition, pages
Springer Nature, 2026
Keywords
Circular economy, Circularity indicators, Environmental assessment, Multi-storey wood building, Timber construction
National Category
Environmental Engineering
Research subject
Technology (byts ev till Engineering), Sustainable Built Environment; Technology (byts ev till Engineering), Civil engineering
Identifiers
urn:nbn:se:lnu:diva-149724 (URN)10.1007/s43615-026-01082-z (DOI)2-s2.0-105046499685 (Scopus ID)
Projects
Competitive timber structures – Resource efficiency and climate benefits along the wood value chain through engineering design
Funder
The Kamprad Family Foundation, AP14870295Knowledge Foundation, 20230005
Available from: 2026-09-22 Created: 2026-09-22 Last updated: 2026-11-16Bibliographically approved
Binder, E., Kuck, E., Bertram, C., Shehadeh, Z., Schweigler, M., Sandhaas, C. & Bader, T. K. (2025). Moisture Dependence Of Mechanical Properties Of Beech And Birch In Compression Perpendicular To Grain And Rolling Shear. In: Proceedings from the 14th World Conference on Timber Engineering Advancing Timber for the Future Built Environment Wcte 2025: . Paper presented at 14th World Conference on Timber Engineering Advancing Timber for the Future Built Environment (WCTE 2025), Brisbane, Australia, 22 - 26 June, 2025 (pp. 681-687). Curran Associates, Inc.
Open this publication in new window or tab >>Moisture Dependence Of Mechanical Properties Of Beech And Birch In Compression Perpendicular To Grain And Rolling Shear
Show others...
2025 (English)In: Proceedings from the 14th World Conference on Timber Engineering Advancing Timber for the Future Built Environment Wcte 2025, Curran Associates, Inc. , 2025, p. 681-687Conference paper, Published paper (Refereed)
Abstract [en]

The forests in Europe are changing in response to climate change, resulting in an increased proportion of hardwood species in mixed forests. Mechanical characterization of hardwood species, an understudied area in the past, is now gaining prominence in research. Our experimental investigation of moisture dependence of mechanical strength of South Swedish hardwoods encompassed the species beech and birch and relative humidity levels of 40, 65, and 85 % at 20 °C. Mechanical strength was determined on two different scales, namely on the board level, which includes effects of the cylindrical orthotropy of the annual ring structure of wood, and on the material level, where this influence is minimized due to the small specimen size. For these different scales, different experimental setups were used, withasimilar experimental evaluation. The results showed that compressive strength perpendicular to the grain increased with decreasing moisture content at both scales. Material level tests resulted in higher compressive strengths compared to the board level. Conversely, rolling shear strength was consistently higher on the board level than on the material level. The dependence of the rolling shear strength on the moisture content was distinct on the board level, but not on the material level.

Place, publisher, year, edition, pages
Curran Associates, Inc., 2025
Keywords
compression test, different length scales, hardwood, moisture dependence, rolling shear test, strength evaluation
National Category
Wood Science
Identifiers
urn:nbn:se:lnu:diva-142924 (URN)10.52202/080513-0085 (DOI)2-s2.0-105010281513 (Scopus ID)9798331320898 (ISBN)
Conference
14th World Conference on Timber Engineering Advancing Timber for the Future Built Environment (WCTE 2025), Brisbane, Australia, 22 - 26 June, 2025
Available from: 2025-12-23 Created: 2025-12-23 Last updated: 2026-01-12Bibliographically approved
Śliwa-Wieczorek, K., Derkowski, W. & Binder, E. (2024). Krótkoterminowe testy pełzania ścinanych połączeń klejonych w kompozytach drewniano-betonowych: Short-term creep test of shear adhesive jointsin Timber-Concrete Composites. Materiały Budowlane (2), 6-10
Open this publication in new window or tab >>Krótkoterminowe testy pełzania ścinanych połączeń klejonych w kompozytach drewniano-betonowych: Short-term creep test of shear adhesive jointsin Timber-Concrete Composites
2024 (Polish)In: Materiały Budowlane, ISSN 0137-2971, no 2, p. 6-10Article in journal (Refereed) Published
Abstract [pl]

W artykule przedstawiono wyniki badań krótkotrwałych i reologicznych przyrostu odkształceń w teście wypychania (push-out test) w przypadku dwuzakładkowych połączeńklejonych. Łącznie przebadano 15 próbek złożonych z elementów wykonanych z drewna klejonego krzyżowo (CLT) oraz prefabrykowanych płyt betonowych. Połączenie między elementami wykonano jako klejone z użyciem innowacyjnych prefabrykowanych złączy podatnych o grubości 3 mm, w trzech konfiguracjach powierzchni klejenia. Celem badań było określeniewpływu geometrii połączenia klejonego na początkowy przyrostodkształceń w czasie. Wykazano, że pełzanie przebiega nieliniowo w czasie t1 = 800 s niezależnie od powierzchni klejenia, a następnie zwiększa się w sposób liniowy. W przeprowadzonych badaniach złączy pasmowych uzyskano przyrost początkowegopełzania o ok. 10% mniejszy w przypadku złączy ułożonychw kierunku obciążenia niż w kierunku prostopadłym. Wykazano również, że wartości pełzania nie są wprost proporcjonalnedo wielkości naprężenia ścinającego.

Abstract [en]

This paper presents the results of a study of short-termrheological strain increments in a push-out test for double-lapglued joints. A total of 15 specimens consisting of crosslaminated timber (CLT) elements and precast concrete slabs weretested. The joint between the elements was made as a glued jointusing innovative 3 mm thick prefabricated flexible jointsin threebonding configurations. The aim of the study was to investigatethe influence of the adhesive joint geometry (typeAwith 600 cm2glue, B – 200 cm2 in strips parallel to the load axis and C – 200 cm2in strips in the perpendicular direction) on the initial deformationincrease over time. Creep phenomenon was shown to be nonlinear for an initial time range of t1 = 800 s regardless of theadhesive area, and then to increase in a linear manner. In the testscarried out on strip joints, the increments of initial creep wereobtained to be about 10% smaller for joints arranged in the loaddirection than for those arranged in the perpendicular one. It wasalso shown that the creep values are not directly proportional tothe magnitude of the shear stress.

Place, publisher, year, edition, pages
Wydawnictwo SIGMA-NOT, sp. z.o.o., 2024
Keywords
adhesive joints, creep, double lap push-out tests, experiments, flexible polyuretans, timber-concrete composites, pełzanie; kompozyty drewniano-betonowe; dwuzakładkowe testy ścinania; testy wypychania; poliuretanowe złącza podatne
National Category
Building Technologies
Research subject
Technology (byts ev till Engineering), Civil engineering
Identifiers
urn:nbn:se:lnu:diva-128030 (URN)10.15199/33.2024.02.02 (DOI)2-s2.0-105028639503 (Scopus ID)
Available from: 2024-02-27 Created: 2024-02-27 Last updated: 2026-02-12Bibliographically approved
Śliwa-Wieczorek, K., La Scala, A., Derkowski, W. & Binder, E. (2024). Longitudinal Shear in Timber–Concrete Composites with Flexible Adhesive Connections: Experimental and Numerical Investigations. Materials, 17(24), Article ID 6055.
Open this publication in new window or tab >>Longitudinal Shear in Timber–Concrete Composites with Flexible Adhesive Connections: Experimental and Numerical Investigations
2024 (English)In: Materials, E-ISSN 1996-1944, Vol. 17, no 24, article id 6055Article in journal (Refereed) Published
Abstract [en]

Timber–concrete composites are established structural elements to combine the advantageous properties of both materials by connecting them. In this work, an innovative flexible adhesive connection in different configurations is investigated. Load-bearing capacity, stiffness, and the failure modes were first experimentally investigated by performing push-out tests. Subsequently, a numerical evaluation using ABAQUS 2017/Standard software was carried out in order to develop a three-dimensional numerical model. The Cohesive Zone Model (CZM) is employed to represent the adhesive characteristics at the contact areas between the Cross-Laminated Timber (CLT) and concrete elements. Three different connection configurations were evaluated, each consisting of five push-out specimens. The study investigates the impact of bonding surface area and the alignment of prefabricated glue strips with the load direction on the connection’s longitudinal shear load-bearing capacity, stiffness, and slip modulus. In addition, the impact of cyclic loads and the impact of time on displacements were analyzed. The average load capacity of the full surface connection (type A) is 44.5% and 46.2% higher than the vertical adhesive strips (type B) and the horizontal adhesive strips (type C), respectively. However, the initial stiffness of the tested joints depends on the orientation of the prefabricated adhesive fasteners, being approximately 20% higher when the bonding elements are aligned parallel to the load direction compared to when they are oriented perpendicularly.

Place, publisher, year, edition, pages
MDPI, 2024
Keywords
shear, timber–concrete-composites, flexible adhesive, load–slip curve, stiffness, numerical analysis
National Category
Building Technologies
Research subject
Technology (byts ev till Engineering), Civil engineering
Identifiers
urn:nbn:se:lnu:diva-136968 (URN)10.3390/ma17246055 (DOI)001384896200001 ()2-s2.0-85213265576 (Scopus ID)
Note

Knowledge Foundation, 20230005

Available from: 2025-02-24 Created: 2025-02-24 Last updated: 2025-04-02Bibliographically approved
Akter, S. T., Binder, E. & Bader, T. K. (2023). Moisture and short-term time-dependent behavior of Norway spruce clear wood under compression perpendicular to the grain and rolling shear. Wood Material Science & Engineering, 18(2), 580-593
Open this publication in new window or tab >>Moisture and short-term time-dependent behavior of Norway spruce clear wood under compression perpendicular to the grain and rolling shear
2023 (English)In: Wood Material Science & Engineering, ISSN 1748-0272, E-ISSN 1748-0280, Vol. 18, no 2, p. 580-593Article in journal (Refereed) Published
Abstract [en]

Material properties of wood under compression perpendicular to the grain and rolling shear are important for the engineering design of timber structures. This regards the short-term stiffness and strength, their dependence on the moisture content of wood, as well as the time-dependent behavior. Norway spruce clear wood properties in the transverse plane of wood were studied inan experimental campaign exploiting an earlier developed biaxial test setup. The moisture dependence of the stiffness and strength and the short-term time-dependent creep deformations under compression in the radial direction and under rolling shear were characterized. Loading and unloading stiffness, as well as the strength, were determined in quasi-static tests at five different moisture contents from 4% to 29%. The elastic and viscous stiffnesses were identified in creep tests at three compressive stress levels of 0.50, 0.75, and 1.00 N/mm2, and at two rolling shear stress levels of 0.33 and 0.50 N/mm2. The test data complements the existing experimental database, especially with novel data regarding the moisture dependence of the rolling shear strength, which showed less moisture dependence than the compressive strength perpendicular to the grain. The results of the creep tests revealed different material properties for the different loading and material directions of wood.

Place, publisher, year, edition, pages
Taylor & Francis Group, 2023
National Category
Building Technologies Wood Science
Research subject
Technology (byts ev till Engineering), Civil engineering
Identifiers
urn:nbn:se:lnu:diva-111337 (URN)10.1080/17480272.2022.2056715 (DOI)000777908800001 ()2-s2.0-85125040071 (Scopus ID)
Available from: 2022-04-14 Created: 2022-04-14 Last updated: 2025-08-13Bibliographically approved
Gikonyo, J., Binder, E., Schweigler, M. & Bader, T. K. (2023). Numerical Modelling of a Cross-Laminated Timber-to-Concrete Dowel-Type Connection Using the Beam-on-Foundation Model. In: Anders Q. Nyrud, Kjell Arne Malo, Kristine Nore (Ed.), Proceedings from the 13th World Conference on Timber Engineering 2023: . Paper presented at World Conference on Timber Engineering 2023 (WCTE 2023), 19-11 June, Oslo (pp. 3101-3110). Oslo, Norway: World Conference on Timber Engineering (WCTE)
Open this publication in new window or tab >>Numerical Modelling of a Cross-Laminated Timber-to-Concrete Dowel-Type Connection Using the Beam-on-Foundation Model
2023 (English)In: Proceedings from the 13th World Conference on Timber Engineering 2023 / [ed] Anders Q. Nyrud, Kjell Arne Malo, Kristine Nore, Oslo, Norway: World Conference on Timber Engineering (WCTE) , 2023, p. 3101-3110Conference paper, Published paper (Refereed)
Abstract [en]

The aim of the research presented herein is to investigate the mechanical behaviour of cross-laminated timber (CLT)-to-concrete dowel-type connections. For reliable timber-concrete-composite structures, mechanical connections between the two construction materials are of great importance. This paper investigates the nonlinear load-displacement behaviour, giving access to the stiffness and strength, as well as ductile connection failure modes, of a CLT-to-concrete composite connection using a Beam-on-Foundation (BoF) model. The latter is a numerical model that utilizes non-linear springs for the interaction between the fastener and the surrounding CLT and concrete materials. The influence of: (i) fastener diameter, (ii) initial slip, (iii) concrete embedment properties, and (iv) axial fastener resistance due to friction, on the connection shear capacity and slip modulus, was investigated in a parameter study. The nonlinear load-displacement response, connection stiffness and strength predicted by the BoF model were moreover compared to laboratory tests and the European Yield Model (EYM), which supported the validity of the BoF model. In addition, it was shown that the BoF model could enhance the prediction of the slip modulus compared to the current design regulations in Eurocode 5.

Place, publisher, year, edition, pages
Oslo, Norway: World Conference on Timber Engineering (WCTE), 2023
National Category
Wood Science Building Technologies
Research subject
Technology (byts ev till Engineering), Civil engineering; Technology (byts ev till Engineering), Forestry and Wood Technology
Identifiers
urn:nbn:se:lnu:diva-123349 (URN)10.52202/069179-0404 (DOI)2-s2.0-85171788117 (Scopus ID)9781713873297 (ISBN)9781713873273 (ISBN)
Conference
World Conference on Timber Engineering 2023 (WCTE 2023), 19-11 June, Oslo
Available from: 2023-07-24 Created: 2023-07-24 Last updated: 2025-05-05Bibliographically approved
Śliwa-Wieczorek, K., Derkowski, W., Binder, E., Kwiecień, A., Zając, B., Halilovic, E. & Lotinac, S. (2023). Shear Stiffness and Capacity of PolyUrethane Flexible Joint in Timber-Concrete Composites. In: Alper Ilki, Derya Çavunt, Yavuz Selim Çavunt (Ed.), Building for the Future: Durable, Sustainable, Resilient: Proceedings of the fib Symposium 2023 - Volume 1 (pp. 476-485). Istanbul, Turkey: Springer
Open this publication in new window or tab >>Shear Stiffness and Capacity of PolyUrethane Flexible Joint in Timber-Concrete Composites
Show others...
2023 (English)In: Building for the Future: Durable, Sustainable, Resilient: Proceedings of the fib Symposium 2023 - Volume 1 / [ed] Alper Ilki, Derya Çavunt, Yavuz Selim Çavunt, Istanbul, Turkey: Springer, 2023, p. 476-485Chapter in book (Refereed)
Abstract [en]

Structural floor systems made of Timber-Concrete Composites (TCC) slabs are becoming more and more popular in office and residential buildings as well as in systems used for the renovation of old ceilings. Timber elements can be constructed as beams or solid slabs (massive CLT). Regardless of the main structural layout, individual components require using interlayer connections, which provide composite action in cross-sections. The most used connection types for TCC are mechanical fasteners, grooved or notched connections, and bonded shear joints. Bonded connections with rigid thin-layer adhesives provide high load capacity, but they are characterized by brittle failure due to their low ductility and introduced stress concentrations. An innovative flexible adhesive joint that ensures the transfer of high loads and high deformations simultaneously is presented in the paper. This connecting structural element, named PolyUrethane Flexible Joint (PUFJ) was examined experimentally in double shear lap tests of connections formed between two external CLT slabs of dimension 120 × 350 × 400 mm3 and a central concrete slab of dimension 100 × 250 × 400 mm3. Shear connections between the composite elements were made of a two-component polyurethane PS type adhesive layer of thickness 3 mm. The tested specimens were prepared in two variants of the application: wet application in the form of liquid adhesive and dry application in the form of prefabricated polyurethane layer glued to the elements by thin polyurethane adhesive. The effect of the adhesive application method on the stiffness and capacity of the TCC joint was investigated. In the paper, the analysis of the experimental tests’ results is presented.

Place, publisher, year, edition, pages
Istanbul, Turkey: Springer, 2023
Series
Lecture Notes in Civil Engineering, ISSN 2366-2557 ; 349
Keywords
Timber–Concrete–Composites, Double Shear Lap Test, Interface Shear, Flexible Adhesive Joint, Polyurethane
National Category
Building Technologies
Research subject
Technology (byts ev till Engineering), Civil engineering
Identifiers
urn:nbn:se:lnu:diva-121838 (URN)10.1007/978-3-031-32519-9_46 (DOI)2-s2.0-85163944306 (Scopus ID)9783031325199 (ISBN)9783031325182 (ISBN)
Available from: 2023-06-14 Created: 2023-06-14 Last updated: 2025-04-30Bibliographically approved
Binder, E., Derkowski, W. & Bader, T. K. (2023). Short-term creep tests for shear connections of timber-concrete-composite slabs. In: J.F. Silva Gomes (Ed.), Experimental Mechanics in Engineering and Biomechanics: Proceedings ICEM2020th International Conference on Experimental Mechanics, Porto 2-7 July 2023. Paper presented at ICEM20 - 20th International Conference on Experimental Mechanics, Porto 2-7 July 2023 (pp. 957-958). INEGI-Instituto de Engenbaria Mecanica e Gestao Industrial, Article ID 19914.
Open this publication in new window or tab >>Short-term creep tests for shear connections of timber-concrete-composite slabs
2023 (English)In: Experimental Mechanics in Engineering and Biomechanics: Proceedings ICEM2020th International Conference on Experimental Mechanics, Porto 2-7 July 2023 / [ed] J.F. Silva Gomes, INEGI-Instituto de Engenbaria Mecanica e Gestao Industrial, 2023, p. 957-958, article id 19914Conference paper, Oral presentation with published abstract (Other academic)
Abstract [en]

As long-term investigations are often too time- and cost-consuming, short-term experimentsare introduced for investigating the behaviour of connections in timber-concrete-compositeelements. The paper presents a proposal for short-term double shear tests with adhesive andmechanical connections for investigating their time-dependent behaviour. The proposedevaluation method determines the elastic and visco-elastic parts of the slip modulus of theconnection. The validity of the identified parameters needs to be verified by long-term tests.

Place, publisher, year, edition, pages
INEGI-Instituto de Engenbaria Mecanica e Gestao Industrial, 2023
Keywords
composite structures, double shear test, timber-concrete-composite, creep
National Category
Composite Science and Engineering
Research subject
Technology (byts ev till Engineering), Civil engineering
Identifiers
urn:nbn:se:lnu:diva-123405 (URN)9789895475674 (ISBN)9789895475667 (ISBN)
Conference
ICEM20 - 20th International Conference on Experimental Mechanics, Porto 2-7 July 2023
Available from: 2023-08-01 Created: 2023-08-01 Last updated: 2025-02-04Bibliographically approved
Organisations
Identifiers
ORCID iD: ORCID iD iconorcid.org/0000-0002-5699-4492

Search in DiVA

Show all publications